The EXM1A is designed for working with multipurpose hobby or small micro controller project that helps you build your circuit prototype easier with soldering pad. (or working area) This board also has built-in essential circuit that is usually used for your projects such as voltage regulator, and two channel of RS-232C line driver.

Package Contents

• EXM1A Board
• Manual
• 3 Month Factory Warranty

This module is an expansion module for interfacing with microcontroller system. Its outputs are a load controller for both AC and DC with maximum 10 Ampere. There are standard 6-pin connecting interface and IDC-10 which can be connected with other microcontrollers. Equipped with bit jumper for output selection.

Package Contents

• EXP4R24V Board
• Manual
• 3 Month Factory Warranty

This board is an interface module for microcontroller. There are four channels of digital input and four channels of relay output. The digital input circuit is installed an opto-isolator in order to protect the MCU from misusing an external signal. Acceptable voltage range for this module is between 12 and 24 VDC. For the output part, there is a SPDT relay at 5A/220VAC.

Package Contents

• EXP8IO24 Board
• Manual
• 3 Month Factory Warranty

This module is a testing tool for microcontroller system. This module supports both analog and digital signal such as digital input, digital output, pulse signal, debounce signal, piezo speaker and analog voltage reference etc. It’s convenient to use and connect to other microcontroller boards with IDC-10 connector.

Package Contents

• IOTESTER Board
• Manual
• 3 Month Factory Warranty

This module is for converting USB to Serial (TTL) signal. FT232RL chip is integrated on the board to proide much functionality - generated clock circuit and EEPROM. Signal link is designed in DIP-28 pins (600 mil) for ease of use. This converter provides two way serial communications signal conversion betweenthe TTL (Transistor Transistor Logic) output to and from a personal computer USB port using virtual serial COM port. It can be used on any Micro controller - PIC, Atmel or other which has TTL serial communications.

Package Contents

• USBFT232 Board
• USB Cable
• CD Software
• Manual
• 3 Month Factory Warranty

This is a loading tool for both MCS-51 and AVR microcontrollers. Easy to use with programming in real-time via parallel port in In-System-Programming mode or ISP; moreover, this module is designed to support many MCUs as following:

-- MCS-51 --
AT89S51/52/53, AT89S2051/4051/8252/8253, AT89LP2052/4052
-- AVR --
AT90S1200/2313/2333/2343/4414/4433/4434/8515/8535, ATMEGA603/103/8515/8535/8/15/161/162/163/169/32/323/64/128, ATTINY12/15/22/26/2313

Package Contents

• LPTLOAD1 Module
• M-IDC10-1 Cable
• CD Software
• Manual
• 3 Month Factory Warranty

This is a microcontroller for applying your application project such as a timing controller, counter, and temperature controller. This board is built base-on MCS-51 microcontroller including all necessary parts such as 7-segment display, push button switches, relay output, RS-232C driver, and voltage regulator. MCU PHILIPS P89V51RD2BN is embedded on this board running at 11.0592 MHz. This board is ideal for embedded applications and general purpose controllers. It's easy to connect and interface with many existing equipment for controlling application. Program on a chip via RS232 cable.

Package Contents

• MAP101 Board (P89V51RD2BN)
• M-RS232 Cable
• CD Software
• Circuit Diagram
• 3 Month Factory Warranty

This is a set of MCS-51 starter kit. Learn fundamental programming with C language and apply to many interfaces such as input switch, LEDs, 7-segment, and dot matrix. Each interface is designed independently from a mainboard (MCT02B53) for flexibility and ease of use.

A mainboard (MCT02B53) is based on MCS-51 designed concept supporting 40-pin DIP package. By "In-System-Programming or ISP" mode, data can be programmed on the chip instantly without other external devices.

Package Contents

• MCT02B53 Board (AT89S8253)
• I2C and 1 Wire Device Interface Board
• 4-digit Display and Key Switch Interface Board
• Dot Matrix 8x8 Interface Board
• M-RS232 Cable
• 3 x M-IDC10 Cables
• AT-ISP Cable
• CD Software
• Manual
• 3 Month Factory Warranty

This is a small embedded module based on MCS-51 designed concept supporting 40-pin DIP package. With "In-System-Programming" or ISP mode, data can be programmed on the chip instantly without requiring any other external devices.

Package Contents

• MCT02B52 Board (AT89S52)
• M-RS232 Cable
• AT-ISP Cable
• CD Software
• Manual
• 3 Month Factory Warranty

This is a small embedded module based on MCS-51 designed concept supporting 40-pin DIP package. With "In-System-Programming" or ISP mode, data can be programmed on the chip instantly without requiring any other external devices.

Package Contents

• MCT02B53 Board (AT89S53)
• M-RS232 Cable
• AT-ISP Cable
• CD Software
• Manual
• 3 Month Factory Warranty

This is an embedded board for MCS-51 In-System-Programming (ISP). This board is equipped with many useful digital I/O interface such as LED-logic monitor, DIP switch, LCD port, and proto board for experimenting. This board supports MCU number AT89S8252 and AT89S8253 by ATMEL, and P89C51RD2 by PHILIPS.

Package Contents

• MEB2KPRD Board (P89V51RD2)
• AT-ISP Cable
• M-RS232 Cable
• SERIAL-TO-USB Converter
• CD Software
• Manual
• 3 Month Factory Warranty

This is an embedded board for MCS-51 In-System-Programming (ISP). This board is equipped with many useful digital I/O interface such as LED-logic monitor, DIP switch, LCD port, and working area for experimenting. This board supports MCU number AT89S8252 and AT89S8253 by ATMEL, and P89C51RD2 by PHILIPS.

Package Contents

• MEB2KRD2 Board (P89V51RD2)
• AT-ISP Cable
• M-RS232 Cable
• SERIAL-TO-USB Converter
• CD Software
• Manual
• 3 Month Factory Warranty

This is an embedded board for MCS-51 In-System-Programming (ISP). This board is equipped with many useful digital I/O interface such as LED-logic monitor, DIP switch, LCD port, and working area for experimenting. This board supports MCU number AT89S8252 and AT89S8253 by ATMEL, and P89C51RD2 by PHILIPS.

Package Contents

• MEB2KS52 Board (AT89S52)
• AT-ISP Cable
• M-RS232 Cable
• CD Software
• Manual
• 3 Month Factory Warranty

This is an embedded board for MCS-51 In-System-Programming (ISP). This board is equipped with many useful digital I/O interface such as LED-logic monitor, DIP switch, LCD port, and working area for experimenting. This board supports MCU number AT89S8252 and AT89S8253 by ATMEL, and P89C51RD2 by PHILIPS.

Package Contents

• MEB2KS53 Board (AT89S8253)
• AT-ISP Cable
• M-RS232 Cable
• CD Software
• Manual
• 3 Month Factory Warranty

This board is a programming tool for various MCU including MCS-51, AVR and serial EEPROM (I2C Bus). Program on 8/20/40 pin device via the ZIF socket. Easy to operate with software. Equipped with AUTO-PROGRAM button to complete all functions with one click.

Package Contents

• PMX100 Board
• RS232 Cable
• Serial-To-USB Converter
• CD Software
• Manual
• 3 Month Factory Warranty