EP001 is a beginner kit with little or no previous knowledge of electronics. Basic soldering techniques required for circuit board assembly. It comes with two sets of flashing circuit and sound circuit, and soldering tools including a soldering iron, cutting pliers and a soldering base. This will make learning electronics easy and fun! Just follow our manual and build exciting projects. You can even play electronic games with your friends. Enjoy hours of educational fun while learning about electronics.


Key Features:

• A simple two LED flasher
• An ambulance siren
• A soldering iron
• Cutting pliers
• A soldering base

Use the LX033 to control the speed of your electric motor or brightness of a DC light bulb. Obtain low speed from a DC motor without sacrificing torque. The LX033 is a small assembled device with an on-board trim pot to control the pulse width modulator output. Has automatic voltage selection between 12 and 30 Volt operation. Large spades for ease of connection. Use crimp on or push on connectors (not supplied) or solder directly to the spades.


Key Features:

• Power supply :12-30 VDC.
• Load current : 15A max.
• Output : controlled DC motor by PWM. (Pulse-With-Modulation)
• Range : 0 - 100 %
• Output frequency: ~ 400Hz

Use the LX066 to control the speed of your electric motor or brightness of a DC light bulb. Obtain low speed from a DC motor without sacrificing torque. The LX066 is a small assembled device with an on-board trim pot to control the pulse width modulator output. Has automatic voltage selection for 12 or 30 Volt operation. Large spades for ease of connection. Use crimp on or push on connectors (not supplied) or solder directly to the spades.


Key Features:

• Power supply :12-30 VDC.
• Load current : 30A max.
• Output : controlled speed by PWM. (Pulse-With-Modulation)
• Range : 0 - 100 %
• Output frequency: ~ 400Hz

This is an fully assembled and tested module. Display Module (with 3" Ultra-Bright LEDs) Digit dimensions 46 x 75mm. PCB 63 x 85mm 12VDC, 5 LEDs per segment, also LED for decimal.. Segment current is 15mA, total current 120mA


Key Features:

• Display dimension 46x75 mm. or 1.78x3 inch.
• PCB dimension 63x85 mm. or 2.5x3.3 inch.
• Power supply: 12Vdc.
• Display used: ultra-bright LEDs
• Total current ~ 120 mA.

This is a fully assembled and tested module. Display Module (with 5" Ultra-Bright LEDs) Digit dimensions 72 x 126mm. PCB 90 x 140mm 12 or 24 VDC jumper selectable, 10 LEDs per segment, also 3 LEDs for decimal.


Key Features:

• Display dimension 72x126 mm. or 2.8x5 inch
• PCB dimension 90x140 mm or 3.5x5.5 inch
• Power supply 12 Vdc. or 24 Vdc. (Select jumper)
• Consist 10 LED's per segment and 3 LED's for the decimal point (p)
• Display used: ultra-bright LED's
• Total current ~225 mA. at 12 VDC. and 120 mA. at 24 VDC.

This is an assembled and tested module. Display Module (with 7" Ultra-Bright LEDs) Digit dimensions 100 x 180mm. PCB 136 x 192mm, 20 LEDs per segment, also 5 LEDs for decimal. Segment current is 15mA, total current 435mA at 12V, 225mA at 24VDC


Key Features:

• Display dimension 100x180 mm. or 4x7 inch
• PCB dimension 136x192 mm or 5.4x7.7 inch
• Power supply 12 Vdc. or 24 Vdc. (select jumper)
• Consist 20 LED's per segment and 5 LED's for the decimal point (p)
• Display used: ultra-bright LED's
• At 12 Vdc. : total current ~ 435 mA.
• At 24 Vdc. : total current ~ 225 mA.

This is an assembled and tested module. Display Module (with 9" Ultra-Bright LEDs) Digit dimensions 147.1 x 229.8mm. PCB 161.6 x 240.7mm, 20 LEDs per segment, also 5 LEDs for decimal. Segment current is 60mA at 12VDC or 30mA at 24VDC, total current 435mA at 12V, 225mA at 24VDC


Key Features:

• Display dimension : 147.10x229.80 mm or 5.8x9 inch
• PCB dimensions : 161.60x240.70 mm. or 6.4x9.5 inch
• Power supply : 12Vdc. or 24 Vdc. (select jumper)
• Consist 20 LED's per segment nd 5 LED's for tthe deciml point(p)
• Disply used : ultra-bright LEDs
• Total current ~ 435 mA. at 12 VDC. and 225 mA. at 24 VDC.

This is an assembled and tested module. Display Module (with 3" Ultra-Bright LEDs) Digit dimensions 46 x 75mm for each digit. PCB 250 x 85mm 12VDC, 5 LEDs per segment, also LEDs for decimal and two LEDs for colon point. Segment current is 15mA, total current 495mA


Key Features:

• Display Dimensions: 46 x 75mm or 1.78 x 3 inches
• PCB Dimensions: 250 x 85mm or 9.85 x 3.35 inches
• Power supply: 12 VDC
• Display used: ultra-bright LEDs
• Consist: 5 LEDs per segment and 1 LED for the decimal point, 2 LEDs for colon
• Segment current at 12 VDC: 15mA
• Decimal point current at 12 VDC: 15mA
• Colon current at 12 VDC: 15mA
• Total current: 495mA

This is an assembled and tested module. Driver Module for use with a single seven segment MX display. For use with TTL, your own logic, or microprocessors. 12VDC, common cathode or common anode.


Key Features:

• For use driver seven segment display ( 3",5",7" and 9" )
• Power supply : 12 Vdc. or 24 Vdc.
• Segment use type common cathode.
• Input voltge : min 4.5 Vdc. ( common cathode or anode )

This is an assembled and tested module. 4 Digits Multiplexer Driver Module for use with multiple MX displays. 12VDC, common anode.


Key Features:

• For use with the seven segment display 3", 5", 7", 9" or MX006
• Input : connected to the multiplex
• Output : common anode
• Power supply : 12 Vdc.

This is an assembled and tested module. 1 Digit Up/Down Counter with Start / Preset point counter. Max. input frequency 15kHz, Power supply 5 to 12VDC/max 80mA at 12VDC.


Key Features:

• Power supply : 5 to 12 Vdc./max 80 mA. at 12 Vdc.
• Used for count unit
• For use wih external display able select display type common anode or common cathode.
• Up / down counter selection.
• Maximum input frequency (CI) : 15 KHz
• Start / preset point counter.
• A reset is available to reset the entire counter to zero.
• Select the display of decimal point.

This is an assembled and tested module. Application using circuit for photography etc.


Key Features:

• Power supply 220 VAC.
• Light sensitivity : adjustable.
• Flash - tube use light output of the electrical energy : 3 watts / second.
• LDR used for light detection.

This is an assembled and tested module. Infra Red Tx / Rx Sensor Module 30 Feet with delay timer adjustable between 1 to 10 seconds. Power supply TX: 12VDC / 20mA max, RX: 12VDC with signal 15ma,without signal 50mA.


Key Features:

• Infrared Sensor Module ~ 30 Feet.
• Power supply for transmitter: 12 VDC 20mA max.
• Power supply for receiver: 12 VDC with signal 15mA, without signal 50mA.
• The OUT point output is active "HIGH" when the RX has signal and is active "LOW" when the TX has no signal.
• Delay Timer: adjustable between 1 to 10 second.
• The operation can be reflective or barrier.
• Detecting distance for reflective is approx. 3 ft.
• Detecting distance for barrier is approx. 10 - 30 ft.